Kommentar:
Einfügen von HTML im Kommentar:
Link einfügen: <a href="LINKURL" target="_blank">LINKTITEL</a>
Bild einfügen: <img src="BILDURL">
Text formatieren: <b>fetter Text</b>  <i>kursiver Text</i> <u>unterstrichener Text</u>
Kombinationen sind auch möglich z.B.: <b><i>fetter & kursiver Text</i></b>
C2 Quellcode formatieren: <code>Quellcode</code>
ASM Quellcode formatieren: <asm>Quellcode</asm>
(Innerhalb eines Quellcodeabschnitts ist kein html möglich.)
Wichtig: Bitte mache Zeilenumbrüche, bevor Du am rechten Rand des Eingabefeldes ankommst !  
> Hallo leute und ins besondere Martin und Andre, > > es arbeitet! Habe das neues betriebssystem geladen. Info jetzt mit richtiger datum usw. > > Vielen dank! Aufs zum naechstem problem :-) > > Gr, > > Bart > > > Hi guys, > > > > thanks a lot, the remarks from Andre sound very promissing. I will check this as soon as I get > > home and I will inform you all about my findings. > > Maybe my knowledge of the German language is that bad that I&#39;ve overread this in the "Handbuch" > > however I will try this out. > > > > Maybe I have to start a newby section on my homepage since I&#39;m really new with this sort > > of devices. I searched the archive and found a lot of messages dealing with these problems but > > I did not find specifics on what I should or should not see on the unit. > > > > I will keep you posted on my proceedings. > > > > Noch mahl vielen Dank und ich hoffe dass jetzt alles klappt. > > > > Gr, Bart > > > > > Hallo Bart & Martin, > > > > > > > maybe you should remove the unit from the board and use it alone. > > > > The serial can be connected with applied cable directly on the unit too. > > > > Use jumpers to activate the reset and boot, then remove reset jumper, > > > > and after 30 seconds remove boot jumper. > > > > > > > > If it continues to run a program after that procedure, you have a broken unit. > > > > If not, the boot key is not correctly wired on the "Regler Board". > > > > > > The boot-key is correctly wired on the CC2-ReglerBoard > > > I have uploaded the OS many times on CC2-Units mounted on the > > > CC2-ReglerBoard. So there can not be the problem. > > > The only different thing is that the reset takes about one second more time > > > because of the onboard watchdog-circuit. > > > But this would only mean that you must press the boot-key a little bit longer. > > > > > > > > > > > > Tnx Martin for your response, the unit doesn&#39;t show a blank screen, it just stays in hostmodus > > > > > > (when it was in hostmodus before I go through the bootroutine) > > > > > > or it resets and runs a programm (when the unit was running a programm). > > > > > > Whatever I do, I never get a blank screen. > > > > > > Bart, here you misunderstood Martin. There will never be a blank screen !! > > > (Only, if you press boot before connecting the supply) > > > If you try to set the boot-mode there will be <u>no new</u> message. > > > You will further see the last message. > > > e.g. the unit was in hostmode before you set the boot-mode there will > > > further displayed the message "HOSTMODE". > > > If you try to set the boot-mode and the message in the display dosen&#39;t > > > change then you are in the boot-mode. > > > > > > > > > > > > > > > > > The voltage level of the boot line seems to be OK for me. > > > > > > > TTL-low level is below 0,8 Volt. And 2,5 Volt is definitely more than this. > > > > > > > > > > > > > The boot-pin(BSL) is shared with the address-bus for the RAM and FLASH. > > > So you will measure 2,5 volts, but in real there are 0 and 5 volts, because > > > there is activity on the address-bus. > > > > > > regards André H. > > > > > >

Dateianhang: (.gif, .png., .jpg, .zip, .rar)

max. 256kB

max. 256kB